F|Heat: A GIS-based compliance tool for municipal heat planning in Germany
Main Article Content
Abstract
Municipal heat planning is becoming a mandatory element of local climate policy in Germany, yet many smaller municipalities lack geospatial tools that are transparent, reproducible and aligned with the German Heat Planning Act (WPG). This paper presents F|Heat, an open-source QGIS extension that supports early-stage municipal heat planning by automating data acquisition, building-level heat-demand preparation, heat-density and heat-line-density analyses, preliminary district-heating network routing, pipe dimensioning, heat-loss estimation and load-profile generation. The method is demonstrated for a district in Barntrup, North Rhine-Westphalia, Germany. The case study connects 268 buildings with an annual heat demand of 11.9 GWh and generates a 9.1 km preliminary network. Simulated annual heat losses amount to 1.6 GWh with standard insulation and 1.4 GWh with enhanced insulation. Using DN-specific network investment assumptions, the annualised network cost contribution is estimated at 0.042 EUR·kWh-1. The results show that F|Heat can provide a reproducible GIS-based workflow for suitability assessment, status-quo analysis and preliminary district-heating area assessment. The tool does not replace detailed techno-economic optimisation, heat-source assessment or engineering design, but narrows the gap between statutory heat planning requirements and the data-processing capacity of municipalities.
Article Details
Articles published in International Journal of Sustainable Energy Planning and Management are following the license Creative Commons Attribution-NonCommercial-NoDerivs 3.0 Unported (CC BY-NC-ND 3.0)
Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License: Attribution - NonCommercial - NoDerivs (by-nc-nd). Further information about Creative Commons
Authors can archive post-print (final draft post-refereering) on personal websites or institutional repositories under these conditions:
- Publishers version cannot be stored elsewhere but on publishers homepage
- Published source must be acknowledged
- Must link to publisher version
References
[1] International Energy Agency (IEA). Energy Policy Review Germany 2025. https://www.iea.org/reports/germany-2025.
[2] Blanco L, Alhamwi A, Schiricke B, Hoffschmidt B. Data-driven classification of Urban Energy Units for district-level heating and electricity demand analysis. Sustainable Cities and Society 2024;101:105075. https://doi.org/10.1016/j.scs.2023.105075.
[3] Wärmeplanungsgesetz (WPG) 2024. https://www.gesetze-im-internet.de/wpg/BJNR18A0B0023.html (accessed April 3, 2024).
[4] Miocic JM, Schleichert L, Van De Ven A, Koenigsdorff R. Fast calculation of the technical shallow geothermal energy potential of large areas with a steady-state solution of the finite line source. Geothermics 2024;116:102851. https://doi.org/10.1016/j.geothermics.2023.102851.
[5] Schwanebeck M, Krüger M, Duttmann R. Improving GIS-Based Heat Demand Modelling and Mapping for Residential Buildings with Census Data Sets at Regional and Sub-Regional Scales. Energies 2021;14:1029. https://doi.org/10.3390/en14041029.
[6] Divkovic D, Knorr L, Meschede H. Design approach to extend and decarbonise existing district heating systems - case study for German cities. International Journal of Sustainable Energy Planning and Management 2023;38:141–56. https://doi.org/10.54337/ijsepm.7655.
[7] Zeh R, Ohlsen B, Philipp D, Bertermann D, Kotz T, Jocić N, et al. Large-Scale Geothermal Collector Systems for 5th Generation District Heating and Cooling Networks. Sustainability 2021;13:6035. https://doi.org/10.3390/su13116035.
[8] Pfeiffer J, Kunick M. Development of an Integrated Software Workflow for District Heating Network Planning: A Structured Methodological Approach. ACC JOURNAL 2025;31:48–63. https://doi.org/10.2478/acc-2025-0004.
[9] Höffner D, Glombik S. Energy system planning and analysis software—A comprehensive meta-review with special attention to urban energy systems and district heating. Energy 2024;307:132542. https://doi.org/10.1016/j.energy.2024.132542.
[10] Kicherer N, Lorenzen P, Schäfers H. Design of a district heating roadmap for Hamburg. Smart Energy 2021;2:100014. https://doi.org/10.1016/j.segy.2021.100014.
[11] Banze T, Kneiske TM. Open data for energy networks: introducing DAVE—a data fusion tool for automated network generation. Sci Rep 2024;14:1938. https://doi.org/10.1038/s41598-024-52199-w.
[12] Alaa, Unaichi CC. FlexiGIS/FlexiGIS: FlexiGIS: an open source GIS-based platform for modelling energy systems and flexibility options in urban areas 2021.
[13] Alhamwi A, Medjroubi W, Vogt T, Agert C. FlexiGIS: an open source GIS-based platform for the optimisation of flexibility options in urban energy systems. Energy Procedia 2018;152:941–6. https://doi.org/10.1016/j.egypro.2018.09.097.
[14] Vieth J, Westphal J, Speerforck A. A GIS-based Co-Planning Approach for District Heating Networks 2024. https://doi.org/10.46855/energy-proceedings-11423.
[15] Fuchs M, Müller D. Automated Design and Model Generation for a District Heating Network from OpenStreetMap Data, 2017. https://doi.org/10.26868/25222708.2017.562.
[16] Wirtz M. nPro: A web-based planning tool for designing district energy systems and thermal networks. Energy 2023;268:126575. https://doi.org/10.1016/j.energy.2022.126575.
[17] Sporleder M, Rath M, Ragwitz M. Design optimization of district heating systems: A review. Front Energy Res 2022;10:971912. https://doi.org/10.3389/fenrg.2022.971912.
[18] Lambert J, Ceruti A, Spliethoff H. Benchmark of Milp Formulations for District Heating Network Design 2024. https://doi.org/10.2139/ssrn.4688228.
[19] citiwatts - Toolbox n.d. https://citiwatts.eu/ (accessed October 28, 2025).
[20] Fonseca J, Thomas D, Mok R, Hsieh S, Sreepathi BK, Happle G, et al. CityEnergyAnalyst 2025. https://zenodo.org/records/14617664 (accessed November 14, 2025).
[21] Hilpert S, Kaldemeyer C, Krien U, Günther S, Wingenbach C, Plessmann G. The Open Energy Modelling Framework (oemof) - A new approach to facilitate open science in energy system modelling. Energy Strategy Reviews 2018;22:16–25. https://doi.org/10.1016/j.esr.2018.07.001.
[22] Krien U, Kaldemeyer C, Günther S, Schönfeldt P, Simon H, Launer J, et al. oemof.solph 2024. https://zenodo.org/doi/10.5281/zenodo.596235 (accessed November 22, 2024).
[23] Lohmeier D, Cronbach D, Drauz SR, Braun M, Kneiske TM. Pandapipes: An Open-Source Piping Grid Calculation Package for Multi-Energy Grid Simulations. Sustainability 2020;12:9899. https://doi.org/10.3390/su12239899.
[24] Bolgaryn R, Banerjee G, Meinecke S, Maschke H, Marten F, Richter M, et al. Open Source Simulation Software pandapower and pandapipes: Recent Developments. 2023 Open Source Modelling and Simulation of Energy Systems (OSMSES), 2023, p. 1–8. https://doi.org/10.1109/OSMSES58477.2023.10089685.
[25] GreenDelta/Sophena 2025.
[26] Becker G, Klemm C, Vennemann P. Open Source District Heating Modeling Tools—A Comparative Study. Energies 2022;15:8277. https://doi.org/10.3390/en15218277.
[27] THERMOS Project. THERMOS 2021. https://www.thermos-project.eu/home/ (accessed September 3, 2025).
[28] Reiner-Lemoine-Institut. open_plan 2.0 n.d. https://reiner-lemoine-institut.de/projekt/open_plan-2-0-ein-werkzeug-fuer-kommunale-waermeplanung-und-energiesystemanalyse (accessed November 20, 2025).
[29] Knies J. A spatial approach for future-oriented heat planning in urban areas. International Journal of Sustainable Energy Planning and Management 2018;16:3–30. https://doi.org/10.5278/ijsepm.2018.16.2.
[30] Jordahl K, Bossche JV den, Fleischmann M, Wasserman J, McBride J, Gerard J, et al. geopandas/geopandas: v0.8.1 2020.
[31] Hagberg AA, Schult DA, Swart PJ. Exploring Network Structure, Dynamics, and Function using NetworkX, Pasadena, California: 2008, p. 11–5. https://doi.org/10.25080/TCWV9851.
[32] Ortner S, Paar A, Johannson L, Wachter P, Hering D, Pehnt M. Leitfaden Wärmeplanung. ifeu - Institut für Energie- und Umweltforschung Heidelberg gGmbH, Öko-Institut e.V., IER Stuttgart, adelphi consult GmbH, Becker Büttner Held PartGmbB, Prognos AG, et al.; 2024.
[33] LANUK. Raumwärmebedarfsmodell NRW 2024. https://www.opengeodata.nrw.de/produkte/umwelt_klima/energie/kwp/.
[34] Geobasis NRW. Gemarkungen und Fluren n.d. https://www.opengeodata.nrw.de/produkte/geobasis/lk/akt/gmk_flur_shp/.
[35] Statistisches Bundesamt. Zensus2022 Gitterdaten nach Energieträger der Heizung 2022. https://www.zensus2022.de/DE/Ergebnisse-des-Zensus/_inhalt.html (accessed April 14, 2025).
[36] F-Heat/F-Heat_QGIS 2025. https://github.com/F-Heat/F-Heat_QGIS (accessed November 20, 2025).
[37] Arbeitsgemeinschaft für zeitgemäßes Bauen e.V. Wohnungsbau in Deutschland 2011 - Modernisierung oder Bestandsersatz 2011. https://arge-ev.de/arge-ev/publikationen/studien/?12.
[38] CARMEN e.V. SOPHENA Datenbank n.d. https://www.carmen-ev.de/service/sophena/ (accessed August 3, 2016).
[39] Vergleichswerte für den Energieverbrauch von Nichtwohngebäuden. BBSR 2025. https://www.bbsr.bund.de/BBSR/DE/veroeffentlichungen/bbsr-online/2021/bbsr-online-37-2021.html (accessed June 18, 2025).
[40] Dettmar J, Hegger M. Energetische Stadtraumtypen. Strukturelle und energetische Kennwerte von Stadträumen. 1st ed. Bonn & Stuttgart: Fraunhofer IRB Verlag; 2014.
[41] Frondel M, Ritter N. Datenauswertung zum Energieverbrauch der privaten Haushalte differenziert nach Gebäudemerkmalen: Sonderauswertung im Auftrag des Bundesministeriums für Verkehr, Bau und Stadtentwicklung 2012. https://hdl.handle.net/10419/72599.
[42] Walberg D. Typische Energieverbrauchskennwerte deutscher Wohngebäude 2012. https://www.iwu.de/fileadmin/publikationen/vortrag_partner/2012-05-31_Walberg_Vortrag-Typische-Energieverbrauchskennwerte.pdf.
[43] Loga T, Stein B, Diefenbach N. TABULA building typologies in 20 European countries—Making energy-related features of residential building stocks comparable. Energy and Buildings 2016;132:4–12. https://doi.org/10.1016/j.enbuild.2016.06.094.
[44] Lund H, Østergaard PA, Nielsen TB, Werner S, Thorsen JE, Gudmundsson O, et al. Perspectives on fourth and fifth generation district heating. Energy 2021;227:120520. https://doi.org/10.1016/j.energy.2021.120520.
[45] Dochev I, Seller H, Peters I. Spatial aggregation and visualisation of urban heat demand using graph theory. An example from Hamburg, Germany. 2019. https://doi.org/10.13140/RG.2.2.31802.34249.
[46] Röder J, Meyer B, Krien U, Zimmermann J, Stührmann T, Zondervan E. Optimal Design of District Heating Networks with Distributed Thermal Energy Storages – Method and Case Study. International Journal of Sustainable Energy Planning and Management 2021;31:5–22. https://doi.org/10.5278/ijsepm.6248.
[47] REHAU. Nahwärmesysteme RAUTHERMEX und RAUVITHERM 2022. https://www.rehau.com/downloads/99896/rauthermex-rauvitherm-technische-information.pdf (accessed November 15, 2023).
[48] Isoplus. Produktkatalog Isoplus - Doppelrohr 2023. https://www.isoplus.de/fileadmin/data/downloads/documents/germany/products/Doppelrohr-8-Seiten_DEUTSCH_Web.pdf (accessed November 21, 2023).
[49] LOGSTOR Calculator n.d. http://calc.logstor.com/de/energitab/ (accessed November 21, 2023).
[50] Nussbaumer T, Thalmann S. Influence of system design on heat distribution costs in district heating. Energy 2016;101:496–505. https://doi.org/10.1016/j.energy.2016.02.062.
[51] Calixto S, Cozzini M, Manzolini G. A New Method for the Techno-Economic Analysis and the Identification of Expansion Strategies of Neutral-Temperature District Heating and Cooling Systems 2022. https://doi.org/10.2139/ssrn.4263558.
[52] Winter W, Haslauer T. Untersuchungen der Gleichzeitigkeit in kleinen und mittleren Nahwärmenetzen. Euroheat & Power n.d.;09 & 10.
[53] Gesetz zur Einführung einer Kommunalen Wärmeplanung in Nordrhein-Westfalen (Landeswärmeplanungsgesetz NRW – LWPG). n.d.
[54] Krien U, Schönfeldt P, Gplssm, Jnnr, Schachler B, Möller C, et al. oemof/demandlib 2021.
[55] Langreder N, Lettow F, Sahnoun M, Kreidelmeyer S, Wünsch A, Lengning S. Technikkatalog 2024. https://www.kww-halle.de/praxis-kommunale-waermewende/bundesgesetz-zur-waermeplanung (accessed August 2, 2024).
[56] Manz P, Billerbeck A, Kök A, Fallahnejad M, Fleiter T, Kranzl L, et al. Spatial analysis of renewable and excess heat potentials for climate-neutral district heating in Europe. Renewable Energy 2024;224:120111. https://doi.org/10.1016/j.renene.2024.120111.
[57] Manz P, Fleiter T, Billerbeck A, Fritz M, Alibaş Ş, Eichhammer W. Identifying future district heating potentials in Germany: a study using empirical insights and distribution cost analysis. International Journal of Sustainable Energy Planning and Management 2024;40:131–45. https://doi.org/10.54337/ijsepm.8142.
[58] Willenbrink H, Sommer P, Weßeler P. F|Heat - A QGIS Plugin for Municipal Heat Planning 2025. https://zenodo.org/records/12806366 (accessed November 20, 2025).